LIQUI MOLY additives work like vitamins and trace elements in various areas of your vehicle. Our oil additives reduce friction and wear; our fuel additives keep the system clean and guarantee optimum combustion and compression. The benefits all our additives have in common: cleanliness in all systems, and therefore maximum performance coupled with lower fuel consumption. The best basis to make sure you get the maximum pleasure from the cars of your customer for as long as possible.
Article: LM20002 | Cera Tec Wear Protection
Wear protection for engines, transmissions, pumps and compressors. Cera Tec is added to the oil and is self-mixing. Sufficient for 0,13 gal (5 liters) oil volume. With long-term effect for 30,000 miles (50,000 km). Not suitable for use with wet clutches!
Cera Tec is a high-tech ceramic wear protection product for all motor oils. Cera Tec reduces friction and wear due to ceramic compounds that withstand extremely high chemical and thermal loads. Prevents direct metal-to-metal contact, thus increasing the engine service life. The low-friction effect reduces fuel consumption in gasoline and diesel engines.
Article: LM20004 | Hydraulic Lifter Additive
Suitable for all commercial motor oils in gasoline and diesel engines with and without diesel particulate filter (DPF). Tested safe with catalytic converters and turbochargers. Can contents are sufficient for up to 1,5 gal (6 l) motor oil. Not suitable for motorcycles with wet clutches.
Prevents hydro tappet noise. Lubrication holes and ducts in the oil circuit are cleaned. Secures optimal hydro tappet performance. Increases the reliability and travel comfort of the vehicle.
Article: LM2019 | MoS2 Antifriction for Gears
Add MoS2-Antifriction for Gears to the gear oil − mixing takes place automatically during operation. The product is suitable for both mineral- and synthetic-based gear oils. One tube is sufficient for up to 0.5 gal (2 l) of gear oil.
MoS2-Antifriction for Gears is a stabilised solid lubricant concentrate in mineral oil. Due to its high MoS2 content and special additives, it is suitable for all manual motor vehicle transmissions and for axle drives without self-locking differential.
Article: LM2009 | MoS2 Anti-Friction Engine Treatment
Compatible with all types of motoroil. For best results add to motor oil at every oil change. One can treats up to 1.5 gal (6 liter) of oil.
Forms a friction and wear reducing “Moly” film on all sliding surfaces of the engine.
Article: LM2001 | Valve Clean
For all gasoline engines. Suitable for standard and high-octane gas, leaded and unleaded. 150 ml is sufficient for up to 20 gal (75 l) of fuel.
Valve Clean is an ash-free, self-mixing combination of active agents, formulated according to the latest additive, fuel and engine technologies and specially developed to fulfills the demands of today’s engines, fuels and running conditions.
Article: LM2007 | Jectron Fuel Injection Cleaner
Regular use keeps injection system in perfect working order. Add the contents to the fuel tank and repeat every 1,200 miles (2,000 km) or as necessary. Suitable for all gasoline engines.
Gasoline additive keeps the interior injection system clean.
Article: LM2003 | Long-Life Grease + MoS2
For extremely long periods of lubrication and extremely high bearing pressures.
For assembly, maintenance and repairs, with limp-home properties thanks to MoS2. For heavily loaded bearings and joints, spline shafts, threads and guides. For constant velocity drive joints. Operating temperature range: -30 C to +125° C.
Certification complying with DIN 51502: KPF 2 K-30
Article: LM20216 | LM48 Installation Paste
For installation, repair and maintenance in all technical sectors.
High performance MoS2 paste for extreme demands. It adheres even to apparently smooth surfaces. It prevents run-in damage and seizing marks when working on bearings and sliding guides, when pressing bolts and bearing bushings, when pulling on roller bearing rings. For basic lubrication – prevents run-in damage. ”For-life” lubrication of joints and small components. Service temperature: –35 °C to +450 °C.
Article: LM2012 | LM508 Anti-Seize Compound
For the lubrication and corrosion protection of connections exposed to high temperature loading. Chemical and petrochemical industry, power stations, ceramics industry, machines and motorvehicle construction. In the latter case, particularly for screw connections on exhaust bends, silencers and chassis components.
Copper Paste is used especially for high temperatures applications on screw connections and parting faces which are exposed to high temperatures, high pressures and corrosive effects such as screws on compressors, turbine and exhaust systems as well as sparking plug threads. Operating temperature range: — 30 °C to + 1100 °C.
< Back to Previous
